8Bitdo Zero Gamepad on Retropie 4.2!
The 8Bitdo Zero gamepad is a cute little (as in tiny) wireless Bluetooth gamepad, that has a similar button layout of a Super Nintendo game controller. You can use it for playing games on your Windows PC, Mac, Android tablet, Android Smart Phone, iOS devices and Raspberry Pi. You can also connect it to your smart phone and use it as a shutter button to snap pictures, hands free. And, it also connects as a keyboard.
I bought my gamepad from here.
Here is a how to setup the 8Bitdo Zero Bluetooth Gamepad, on Retropie 4.2.
Note: I have only connected the 8Bitdo Zero to my Raspberry Pi 3 and Pi Zero. I have not tried it on anything else yet. And so far, it works decently on Retropie 4.2. As long as the games you are playing don’t require more buttons, than a Super Nintendo controller would. Works well on Nintendo and SNES games!
But at 1st I had a little bit of trouble figuring out how to get it set up correctly. If you have it turned on to connect as the wrong device, it will not set up the buttons to work correctly in the games.
Step 1. Charge the 8Bitdo Zero Gamepad
Plug it in with the included short usb cable and charge it on a usb port of your computer or with a phone charger. It will blink green until it is fully charged and then shut off when done.
Step 2. Getting the Gamepad Ready
Push and hold the start button for 2 seconds. Then you should see it blink. If it blinks more than once in a row, the controller needs to be reset. To reset it, hold down the select button for 2 seconds. Then hold down the start button until it shuts off (8 to 10 sec).
Step 3. Retropie Configuration
With the controller off, enter the Retropie configuration menu and using another usb connected gamepad or keyboard (need to configure the keyboard in the main menu controller configuration, if not already). Then select BLUETOOTH in the menu.
Step 4. Connecting the Gamepad to Bluetooth.
On the next screen, select “Register and Connect to Bluetooth Device” and press OK. You should see a screen saying it’s searching, and then press and hold the start button for 2 seconds. It will start to flash on/off with a blue light, as the Pi searches for a Bluetooth device.
Once found, it should display the mac address and the name of the controller. Then press OK.
(If it doesn’t find it, try it again. If it continues to not find it, you may need to restart retropie. The Bluetooth on the Pi 3 isn’t really good but works most of the time.)
The next screen should show this above with 1. DisplayYesNo at the top selected. Then just choose OK.
If it connected successfully, you should see “Successfully registered and connected to”, and the mac address of the game pad. The blue light should not be blinking at all now.
Note: On the Retropie Github 8Bitdo setup guide, it shows to setup the udev rule for joypad, as described in step 12, found here. I did not do that. I also left the 8Bitdo mapping hack (OFF – new firmware)!
Now press OK and then Cancel on the next screens to get back to the the configuration menu and use the correct button to on the keyboard or other gamepad to exit and get back to the game system screen.
Step 5. Configure Gamepad
Then you will need to go to the main menu and configure the controller buttons.
I just set mine up like a snes controller (used the a for the b button and b for a button and used the L and R buttons as left and right triggers).
Then you should be good to go!
If the gamepad sits idle for a while, they will disconnect. You should be able to reconnect them by holding down the select button for a second or 2. It will flash really fast and then reconnect. If you restart Emulationstation, when you see the Emulationstation screen, press and hold the select button a couple of seconds to reconnect.
Sometimes when it reconnects, it will go haywire and make the system screen scroll fast. Just push any button to make it stop, usually. I have had some issues where it wouldn’t stop and had to do a shutdown or restart by way of ssh (or just unplugged the power).
Also, you may have to go through the Bluetooth setup again, once in a while if you have problems. And, the charge lasts a long time, but if you continue having connection issues, try recharging it.
Anyway! Enjoy playing your games!